Phnom Penh, serving Cambodia and the region

Industry

Dry air, clean nitrogen and stable rooms for sensitive assembly

Dry air and nitrogen for electronics assembly protect solder joints, moisture-sensitive components and placement accuracy. Nexus Turnkey supplies oil-controlled compressed air dried to a stated dew point, on-site nitrogen at the purity your reflow, wave or selective soldering needs, and rooms held at a steady temperature and humidity. Where assembly or testing needs it, we add clean-zone air handling. Every utility is specified against a class you can measure, and monitored.

Automated placement head above a circuit board on an assembly line
Factory cross-section highlighting the air services used in Electronics: Compressed air, Air treatment, Nitrogen, Dehumidification, Cleanroom, HVAC & chillers, Monitoring (AirSight). PRODUCTION HALLN₂+
Fig. · Factory cross-section, air services

Electronics

Dry air and nitrogen for electronics

Electronics lines use air in small, exacting amounts: dry compressed air for placement and handling, nitrogen for soldering and storage, and rooms held at a set temperature and humidity. The lens shows the treatment train, the nitrogen generator beside the line, the clean-zone air handling and the sensors that keep it all in limits.

Air services in focus: Compressed air, Air treatment, Nitrogen, Dehumidification, Cleanroom, HVAC & chillers, Monitoring (AirSight).

Explore electronics

The challenge

Electronics assembly uses air in small amounts with tight limits. Pick-and-place heads, board handling and cleaning nozzles need compressed air free of oil, water and particles. Reflow, wave and selective soldering use nitrogen to reduce oxidation. Moisture-sensitive components and solder paste react badly to humid air, and tropical humidity is high for much of the year. A chilled room in a humid climate also brings condensation risk at doors and on cold surfaces.

The air services an electronics plant needs

Compressed air comes from oil-free or well-filtered generation. A desiccant dryer reaches a low pressure dew point, and coalescing filters and point-of-use filtration finish the job. Each use point is written as an ISO 8573-1 class. See air treatment and compressed air systems.

Nitrogen comes from a PSA generator next to the line, sized for flow and residual oxygen. Small, lower-purity duties can use membrane separation. See nitrogen generators and nitrogen generators against cylinders.

Rooms are held at a steady temperature and relative humidity through humidity control and HVAC and cooling. Where a test or assembly zone needs a particle class, we add HEPA filtration and pressure control. Sensors for dew point, oxygen, temperature and humidity report to one screen.

What we check first

Electronics plants often grow line by line, and their utilities lag behind. Before we propose any equipment, we check four things.

  • Dew point at the machine, not at the dryer. Long runs through hot roof spaces and unused branches let moisture and particles back into dry air. We measure where the air is used.
  • Nitrogen demand per line. Reflow, wave and selective soldering each draw differently at start-up, idle and full production. We log demand before sizing a generator, so you don’t buy purity or capacity you don’t need.
  • Room humidity over a full week. Dock doors, make-up air and chilled surfaces all move the number. A week of logging tells us more than a design sheet.
  • Power quality. Voltage dips can trip compressors, dryers and generators mid-shift. Drives and restart logic should be set for the site supply.

The result is a short list of measured gaps, each linked to a fix, rather than a generic equipment list.

Standards that apply

Typical scope

PackageWhat it usually includes
Compressed airOil-free or filtered generation, desiccant drying, point-of-use filtration
NitrogenPSA or membrane generator, buffer, oxygen analyser
ClimateDehumidification, cooling, sealed rooms, clean zones where needed
MonitoringDew point, oxygen, temperature and humidity with alarms

Use the system selector to frame a brief, or ask design and engineering to specify the utilities for a new line.

Scope

Relevant standards

Standards that commonly shape this industry's air
StandardWhy it matters here
ISO 8573-1:2010Purity classes for compressed air. Placement heads and cleaning nozzles need a tight particle, water and oil class.
IPC/JEDEC J-STD-033Sets handling, dry-packing and dry-storage rules for moisture-sensitive surface-mount devices. Context for dry cabinets and room humidity.
ISO 14644-1:2015Classifies clean zones by particle count, where assembly or test areas require a class.
We design to the standard your process requires. Nexus describes these standards; it does not claim certification against them.

FAQ

Questions engineers ask us

What nitrogen purity do we need for reflow soldering?

It depends on the process, paste and the residual oxygen your engineers specify. A PSA generator lets you select purity rather than paying for the highest grade everywhere. We size the generator to the line's flow and oxygen target and add an analyser.

Do we need a desiccant dryer for electronics?

Often, for air that touches boards or components, because a desiccant dryer reaches a far lower pressure dew point than a refrigerated dryer. General utility air may only need refrigerated drying. We split the plant by use point so you only pay for low dew points where they matter.

What humidity should an SMT room run at?

Your component, paste and ESD programme set the range. In Cambodia, the usual problem is humidity that is too high for paste and moisture-sensitive parts, so dehumidification and sealed rooms come first.

Next step

Specify dry air and nitrogen for your line

Send us your line layout and soldering process. We will size the dry air, nitrogen and room climate to match.

Start typing to search