Glossary
The words engineers use, defined.
73 terms from compressed air, air treatment, dehumidification, air quality and HVAC, each defined in one sentence and explained in plain English with links to the tools and guides that use them.
A
- Activated carbon
- A highly porous carbon that adsorbs vapours and odours, used in compressed air filters to remove oil vapour and in ventilation and exhaust systems to remove VOCs and odour.
- Aftercooler
- A heat exchanger that cools hot compressed air leaving the compressor so that most of its water vapour condenses and can be separated and drained before the dryer.
- AHU (air handling unit)
- A packaged unit of fans, filters, coils and dampers that conditions and moves air for a building or process space through ductwork.
- Air receiver
- A pressure vessel that stores compressed air to buffer demand peaks, stabilise system pressure and reduce compressor cycling.
- AMC (annual maintenance contract)
- A contract under which a service provider maintains equipment over a year or longer for an agreed scope, typically covering preventive maintenance, parts and response to breakdowns.
B
- Baghouse
- A dust collector that filters dusty air through rows of fabric bags, cleaned periodically by pulses of compressed air or by shaking or reverse air.
- Base load
- The steady, minimum air demand a plant draws through a production period, normally carried by fixed-speed compressors running fully loaded.
C
- cfm (cubic feet per minute)
- An imperial unit of volumetric flow, widely used for compressor capacity; 1 m³/min equals about 35.31 cfm.
- Chiller
- A refrigeration machine that cools water or a water-glycol mixture, which is then pumped to air handling units, process equipment or heat exchangers.
- CMH (cubic metres per hour)
- Cubic metres per hour (m³/h), the usual unit for airflow through fans, air handling units, filters, dehumidifiers and emissions control systems.
- Coalescing filter
- A compressed air filter that captures oil and water aerosols by merging fine droplets into larger ones that drain away, along with fine particles.
- Condensate
- The liquid water, usually mixed with oil and dirt, that drops out of compressed air as it is cooled after compression.
- Cooling tower
- A heat rejection unit that cools water by evaporating a small part of it into an airstream, used with water-cooled chillers, compressors and process equipment.
- COP (coefficient of performance)
- The ratio of useful cooling or heating output to electrical power input for a chiller, heat pump or air conditioner, expressed as a dimensionless number.
- Cyclone separator
- A dust separator with no moving parts that spins the airstream in a conical body so that centrifugal force throws particles to the wall and down into a hopper.
D
- Desiccant dryer
- A compressed air dryer that removes water vapour by adsorption onto a desiccant bed, reaching pressure dew points of -40 °C or -70 °C.
- Desiccant rotor
- A slowly rotating wheel impregnated with desiccant that dries air passing through one sector while a heated airstream regenerates another, used in desiccant dehumidifiers.
- Dew point
- The temperature to which air must be cooled, at constant pressure and moisture content, for its water vapour to start condensing.
- Dust collector
- An extraction and filtration system that captures airborne dust at the source and separates it from the conveying air, using cartridges, filter bags or cyclones.
E
- EER (energy efficiency ratio)
- A cooling efficiency ratio of cooling output to power input at stated rating conditions, given in Btu/h per watt in US practice or as a kW/kW ratio in European standards.
- EN 779
- The former European standard for general-ventilation filter classes (G1-G4, M5-M6, F7-F9), superseded by ISO 16890.
- ePM1
- A filter's efficiency against particles of 0.3 to 1 µm under ISO 16890; an 'ISO ePM1' filter captures at least 50% of them.
F
- FAD (free air delivery)
- The volume of air a complete compressor package actually delivers, measured at its outlet and expressed at the conditions of the air drawn in at its inlet.
- FAT (factory acceptance test)
- Testing equipment at the supplier's works before shipment to confirm it is built and performs as specified, witnessed or reviewed by the buyer.
H
- Heat recovery (compressors)
- Capturing the heat a compressor rejects -- from its oil cooler or cooling air -- and using it for process water, boiler feed or space heating instead of dumping it.
- HEPA filter
- A high-efficiency particulate air filter classified under EN 1822-1 or ISO 29463, with H13 and H14 grades capturing at least 99.95% and 99.995% of particles at the most penetrating particle size.
I
- IE motor class
- The international efficiency class of an electric motor under IEC 60034-30-1, from IE1 (standard) to IE4 (super premium), with IE5 (ultra premium) defined in later standards.
- ISO 11011
- The international standard that sets out how to carry out and report an energy-efficiency assessment of a compressed air system.
- ISO 14644
- The international series of standards for cleanrooms and controlled environments; Part 1 classifies air cleanliness by airborne particle concentration, from ISO Class 1 to ISO Class 9.
- ISO 16890
- The international test and classification standard for general-ventilation air filters, which rates filters by their efficiency against PM1, PM2.5 and PM10 particles.
- ISO 8573-1
- The international standard that defines compressed air purity classes for particles, water and oil, written as a three-figure class such as [1:4:1].
K
- kWh/m³ (specific energy)
- The electrical energy a compressed air system uses per cubic metre of air delivered, measured over time at plant level.
L
- Laminar flow (unidirectional airflow)
- Filtered air moving in parallel streams at uniform velocity across a work zone, sweeping particles away before they settle on product or surfaces.
- Leak rate
- The share of a compressed air system's output lost through leaks, usually expressed as a percentage of compressor capacity or as a flow when production is stopped.
- Load/unload control
- A fixed-speed compressor control method that runs the motor continuously and switches the airend between full output and zero output to hold pressure within a band.
M
- Membrane separation (nitrogen)
- A nitrogen generation method that passes compressed air through bundles of hollow polymer fibres, letting oxygen, water vapour and CO₂ permeate out faster than nitrogen.
N
- N+1 redundancy
- A design rule that installs one more unit than needed to meet peak demand, so any single machine can fail or be serviced without losing supply.
- Nm³ (normal cubic metre)
- A cubic metre of gas expressed at stated 'normal' reference conditions of temperature and pressure, so quantities measured under different conditions can be compared.
O
- Oil-free compressor
- A compressor whose compression chamber contains no oil, so no lubricant is introduced into the air it delivers.
- Oil-injected screw compressor
- A rotary screw compressor that injects oil into the compression chamber to seal the rotors, absorb heat and lubricate, then separates it from the air before discharge.
- Oil-water separator
- A unit that separates oil from compressor condensate so the water can be discharged and the oil collected for proper disposal.
P
- P&ID (piping and instrumentation diagram)
- A schematic drawing that shows the process equipment, piping, valves, instruments and control loops of a system and how they connect.
- Packed-bed scrubber
- A wet scrubber in which exhaust gas flows through a column of packing media wetted by a scrubbing liquid, giving a large contact area to absorb soluble gases and odours.
- Pass box
- A small chamber with two interlocked doors set into a cleanroom wall, used to transfer materials between areas of different cleanliness without opening a direct air path.
- PLC (programmable logic controller)
- A rugged industrial computer that reads inputs, runs control logic in real time and drives outputs for machines and systems.
- PM-VSD (permanent-magnet variable speed drive)
- A variable-speed compressor drive that uses a permanent-magnet synchronous motor instead of an induction motor, keeping motor efficiency high across a wide speed range.
- PM2.5
- Airborne particulate matter with an aerodynamic diameter of 2.5 micrometres or less, fine enough to penetrate deep into the lungs.
- Positive pressure (room)
- Keeping a room at a slightly higher air pressure than its surroundings by supplying more filtered air than is extracted, so air leaks outwards and contaminants stay out.
- Pressure dew point (PDP)
- The temperature at which water vapour in compressed air starts to condense, measured at the air's actual line pressure.
- PSA (pressure swing adsorption)
- A gas separation process that produces nitrogen from compressed air by adsorbing oxygen onto carbon molecular sieve under pressure and releasing it when the pressure is lowered.
- ΔP (pressure drop)
- The loss of pressure as air flows through pipes, filters, dryers, hoses and fittings, between the compressor and the point of use.
R
- Refrigerated dryer
- A compressed air dryer that chills the air with a refrigeration circuit to condense and remove water, typically to a pressure dew point of around +3 °C.
- Relative humidity (RH)
- The amount of water vapour in air as a percentage of the maximum it could hold at the same temperature.
- Ring main
- A compressed air distribution header laid as a closed loop, so air reaches each take-off from two directions with lower pressure loss.
- Roots blower
- A rotary lobe blower in which two counter-rotating lobed rotors move pockets of air from inlet to outlet without internal compression, supplying low-pressure air or vacuum.
- Rotary screw compressor
- A positive-displacement compressor in which two meshing helical rotors trap air and reduce its volume continuously as they turn.
- RTO (regenerative thermal oxidiser)
- An emissions control system that destroys VOCs by oxidising them at high temperature, recovering most of the heat in ceramic media beds to keep fuel use low.
S
- SAT (site acceptance test)
- Testing installed equipment and systems on site, under real operating conditions, to confirm they meet the specification before handover.
- SCADA (supervisory control and data acquisition)
- A software system that collects data from plant equipment and controllers, displays it centrally, logs history and raises alarms, with limited supervisory control.
- Sequencer
- A master controller that decides which compressors run, load and stand by in a multi-compressor system, to hold one pressure band with the fewest machines.
- Side-channel blower
- A regenerative blower in which an impeller repeatedly accelerates air through a side channel, building moderate pressure or vacuum at relatively low flow.
- Specific power
- The electrical power a compressor package draws per unit of free air delivered, usually stated in kW per m³/min or kW per 100 cfm at a stated pressure.
T
- Trim compressor
- The compressor in a multi-machine system that follows changes in demand, while base-load machines run fully loaded.
- Turbo blower
- A high-speed centrifugal blower, usually direct-driven by a permanent magnet motor on magnetic or air-foil bearings, delivering oil-free low-pressure air.
- TVOC (total volatile organic compounds)
- A single figure summarising the combined concentration of volatile organic compounds in air, whose value depends on the measurement method and calibration used.
- Two-stage compression
- Compressing air in two stages in series, with an intercooler between them, so each stage works over a smaller pressure ratio and less energy is lost as heat.
U
- Ultrasonic leak detection
- Locating compressed air and gas leaks by detecting the high-frequency sound produced by turbulent flow through the leak, using a handheld or acoustic-imaging instrument.
- Unloaded power
- The electrical power a fixed-speed compressor still draws while running unloaded, delivering no compressed air.
V
- Venturi scrubber
- A wet scrubber that accelerates exhaust gas through a narrow throat where it atomises the scrubbing liquid, capturing fine particles, mists and fumes in the droplets.
- VSD (variable speed drive)
- An electronic drive that varies a compressor motor's speed so air output follows demand instead of switching between full load and unload.
W
- Wet scrubber
- An air pollution control device that removes gases, odours, mists or particles from an exhaust stream by bringing it into contact with a scrubbing liquid.
Z
- Zeolite rotor concentrator
- A slowly rotating honeycomb wheel of hydrophobic zeolite that adsorbs VOCs from a large, dilute exhaust stream and releases them into a much smaller, hotter airstream for destruction.
- Zero-loss drain
- An automatic condensate drain that senses the liquid level and opens only to discharge water, without venting compressed air.
Next step
A term we haven't defined?
Ask us. If it matters to your plant, it probably belongs here.