The problem: tropical air carries moisture into everything
Outdoor air in Cambodia is warm and humid for most of the year, and in the wet season it is close to saturated for long periods. Every open door, every gap in the cladding and every fresh-air intake brings that moisture inside. Once it is in, it ends up in your product.
The damage depends on the industry. In garment and textile plants, fabric and finished goods pick up moisture, which affects handling and weight and invites mould in storage. In warehouses, cartons soften, labels lift and metal parts corrode. Pharmaceutical manufacturers handle powders and tablets that absorb water and change behaviour. Food producers see caking, stickiness and shorter shelf life. Electronics assembly has moisture-sensitive components that need controlled storage.
The usual first response is more air conditioning. It often disappoints. An air conditioner is designed to control temperature. It removes moisture only as a by-product of cooling, and only while it runs. In a space with a modest heat load, or with equipment that is oversized and cycles on and off, the temperature can look right while humidity climbs.
Temperature is what people feel. Humidity is what the product feels.
Our approach: define, calculate, seal, select, prove
Define the target. We agree the condition each zone needs: a relative humidity band, a temperature and, for drier processes, a dew point. The target comes from your product data, your customer’s specification or your quality system. It is not guessed.
Calculate the moisture load. We add up where the moisture comes from: infiltration through the envelope, door openings, ventilation air, people, wet processes and moisture released by the product itself. The design case is the wet season at full production, because that is when the system has to work hardest.
Seal before you size. Every kilogram of water kept out is one the dehumidifier does not have to remove, every hour, for years. We survey the envelope and recommend practical measures: door discipline, fast-acting doors or strip curtains, air locks for busy openings, and sealing of obvious gaps.
Select the technology. Two technologies cover most needs.
- Refrigerant (condensing) dehumidifiers cool the air below its dew point so moisture condenses, then return it to the space. They suit warm spaces with moderate targets, such as garment stores and general warehouses.
- Desiccant rotor dehumidifiers adsorb moisture onto a slowly rotating wheel, which is regenerated with heated air. They reach lower dew points and keep working at low temperatures, which suits pharmaceutical areas, cold stores and dry rooms.
Some sites use both, with a desiccant unit treating fresh air and refrigerant units handling the space.
Distribute and integrate. Dry air has to reach the whole space. We design ducted supply and return so there are no damp corners, and we coordinate the dehumidifiers with existing AHUs and cooling so the systems do not fight each other.
Control and prove. Sensors in each zone, a controller that responds to humidity rather than a timer, alarms when conditions drift, and logged data you can show an auditor.
What’s included
A humidity control project covers the survey and moisture-load calculation, envelope recommendations, equipment selection, ducting and air distribution, electrical and controls, condensate drainage, installation, commissioning against the agreed target and operator training. The scope table on this page sets out each element.
We supply the AirMax dehumidifier range as authorised distributor. That covers portable, commercial, ducted, ceiling-mounted, swimming pool, desiccant rotor and low-temperature units. See industrial dehumidifiers for the families. Filters for the dehumidifiers and air-handling plant come from our filters and media range.
How this fits with the rest of your plant
Humidity, temperature and ventilation are one problem. If your plant also needs process cooling or comfort cooling, we design HVAC and cooling and dehumidification together so each does its own job. In clean areas, humidity control works alongside the filtration and positive pressure covered under air quality and emissions. And compressed air has a humidity problem of its own: moisture in the air lines is handled by dryers, specified by pressure dew point under compressed air systems.
The industries we see this most in are garment and textile, warehousing and logistics, pharmaceutical and healthcare, food and beverage and electronics.
After commissioning, a maintenance contract keeps filters, coils, rotors and sensors in condition, and sensor checks keep the logged data trustworthy.
Commissioning against the target, not the nameplate
A dehumidifier that runs is not proof that a space is controlled. We commission against the condition agreed at the start. Sensors are checked before they are trusted, controllers are set to the target band, and the space is logged across normal operation, including door traffic and shift changes. Where the project allows, we review performance again once the wet season arrives, because that is the design case and the real test.
You receive the logged data, the settings and a simple routine for checking sensors and cleaning filters. If the condition drifts later, the trend usually shows why: a door left open, a filter that needs changing, a new moisture source in the space. The data turns an argument about whether it is damp into a fact you can act on.
Standards literacy
Humidity targets usually come from product specifications, customer requirements or a site’s quality system rather than a single standard. In controlled environments, humidity is often specified alongside particle cleanliness classified under ISO 14644-1. We work from whichever requirement applies to you and design the monitoring to demonstrate it.
For the full method, technologies and worked examples, read our industrial dehumidification guide.
