Why humidity is a production problem, not a comfort problem
In a humid climate, water vapour is a raw material nobody ordered. It arrives with every m³ of outdoor air, every open loading door and every person on shift. Most of the time nobody notices it. Then a powder cakes, a carton softens, a steel coil rusts, a ceiling drips or a batch of finished garments goes mouldy in the warehouse.
Humidity causes five kinds of problem in industry:
- Product damage. Hygroscopic materials absorb water from the air. Powders cake and flow badly, tablets and capsules change hardness or stability, confectionery becomes sticky, and paper, board and textiles change weight and dimensions.
- Process problems. Coatings and adhesives cure differently, packaging seals fail, and moisture-sensitive electronic components can crack during soldering.
- Corrosion. Steel and other metals corrode much faster when surfaces stay damp. ISO 9223, the standard for classifying the corrosivity of atmospheres, uses “time of wetness”: the time during which relative humidity is above 80% at temperatures above 0 °C.
- Mould and hygiene. The US Environmental Protection Agency advises keeping indoor relative humidity below 60%, and ideally between 30 and 50%, to limit mould growth. In food and pharmaceutical plants, condensation on ceilings and pipes is a contamination risk in its own right.
- Static and handling. Very dry air increases static charge generation, which matters for electronics and for some powders and films. In tropical plants the more common electronics issue is the opposite: moisture absorbed by components and boards.
The cost of these problems is rarely on the utility bill. It shows up as rejected batches, claims from customers, cleaning, repainting and stock written off. That is why the first step in any humidity project is to agree what damage you are preventing and what condition prevents it.
In a humid climate, water vapour is a raw material nobody ordered.
Psychrometrics without the jargon
Psychrometrics is the study of moist air. You do not need the full chart to make good decisions, but you do need three terms, used correctly.
Relative humidity
Relative humidity (RH) is the amount of water vapour in the air compared with the maximum the air could hold at the same temperature, expressed as a percentage. Strictly, it is the ratio of the actual vapour pressure to the saturation vapour pressure at that temperature.
The key word is “same temperature”. Warm air can hold more water vapour than cool air. So if you warm a room without adding or removing water, RH falls. If you cool it, RH rises. RH alone does not tell you how much water is in the air. 60% RH at 30 °C contains much more water than 60% RH at 20 °C.
Dew point
Dew point is the temperature at which air would become saturated (100% RH) if you cooled it without changing its moisture content. Cool any surface below the air’s dew point and water condenses on it.
Dew point depends only on how much water vapour is in the air. It does not change when the room warms up or cools down, so it is a stable, honest number for specifying a dry space. It is also the number that predicts condensation: if the dew point of the room air is above the temperature of a cold pipe, a chilled product or a steel delivery that arrived from an air-conditioned truck, that surface will sweat.
Do not confuse it with pressure dew point, which is used for compressed air and refers to the dew point at line pressure. Our compressed air guide explains that difference.
Absolute humidity and humidity ratio
Absolute humidity is the mass of water vapour in a volume of air, in g/m³. Engineers usually prefer the humidity ratio (also called moisture content or mixing ratio): the mass of water vapour per kilogram of dry air, in g/kg. Because it is referred to a mass of dry air, it does not change as air warms, cools or moves through a duct, which makes it the right unit for moisture load calculations.
| Term | What it measures | Changes with temperature? | Best use |
|---|---|---|---|
| Relative humidity | Water vapour relative to saturation | Yes | Product limits stated in RH, comfort, mould risk |
| Dew point | Temperature at which condensation starts | No | Specifications, condensation risk, control |
| Humidity ratio | g of water per kg of dry air | No | Moisture load calculations |
Why cooling a room can make it damper
Here is the physics in numbers, calculated from standard psychrometric relationships at sea-level pressure:
- Outdoor air at 32 °C and 75% RH has a dew point of about 27 °C and a humidity ratio of roughly 22.7 g/kg.
- A room held at 24 °C and 50% RH has a dew point of about 13 °C and a humidity ratio of roughly 9.3 g/kg.
- If that room air is cooled to 18 °C without removing water, its RH rises to about 72%.
Two lessons follow. First, every kilogram of outdoor air that enters the room brings in more than twice the water the room can keep. Second, any surface in contact with outdoor air that is cooler than about 27 °C will condense: chilled water pipes, the outside of cold stores, the underside of an air-conditioned roof, a pallet of product moved out of a cool room.
Two ways to take water out of air
Almost all industrial dehumidification uses one of two principles: condensing water on a cold surface, or adsorbing it onto a desiccant.
Refrigerant (condensing) dehumidifiers
A refrigerant dehumidifier draws air across a cold evaporator coil. When the coil surface is below the air’s dew point, water condenses and drains away. The air is then reheated across the condenser coil and returned to the room, warmer and drier than it arrived.
Refrigerant dehumidifiers work best in warm, humid air at normal room temperatures, which is exactly the condition of many tropical production and storage spaces. They are energy-efficient there, because there is plenty of water to condense. Their limits:
- As the target dew point falls, the coil must run colder. Below a certain coil temperature, water freezes on the coil and the unit spends time defrosting.
- At low room temperatures, capacity falls sharply.
- They add heat to the room: the heat removed from the air, plus the compressor’s energy.
Desiccant rotor dehumidifiers
A desiccant rotor dehumidifier uses a slowly turning wheel impregnated with a desiccant, commonly silica gel. Process air passes through most of the wheel face, and the desiccant adsorbs water vapour from it. A smaller sector of the wheel is swept by heated reactivation (regeneration) air, which drives the water off and carries it outside.
Desiccant rotors keep working at low temperatures and can reach dew points that a cooling coil cannot reach without freezing. Their limits:
- They need heat for regeneration: electric, steam, hot water or gas. That energy is part of the running cost and should be designed in, not discovered later.
- The dry air leaves warmer than it entered, because of the heat of adsorption and heat carried over from the regeneration sector. In a temperature-controlled room, post-cooling is usually part of the design.
- The reactivation air needs its own intake and exhaust routes.
Choosing between them
| Factor | Refrigerant | Desiccant rotor |
|---|---|---|
| Best range | Warm, humid air, moderate dryness | Low temperatures, low dew points |
| Energy source | Electricity for the compressor | Electricity for fans plus regeneration heat |
| Air leaving the unit | Warmer, drier | Warmer, much drier |
| Low-temperature spaces | Capacity falls, coil may frost | Performance largely maintained |
| Typical uses | Warehouses, garment stores, general production | Pharma dry rooms, cold stores, powders, electronics |
In practice, many systems combine the two. A cooling coil, often fed by a chiller, removes the bulk of the water from warm, humid fresh air, and a desiccant rotor polishes the air to the final dew point. The cooling coil does the cheap work; the desiccant does the work only it can do.
Let the cooling coil do the cheap work and the desiccant do the work only it can do.
Formats
Dehumidifiers come in several physical forms, and the right one depends on the space more than on the technology:
- Portable and mobile units for temporary duties, drying out after water damage, or proving a concept before a permanent installation.
- Commercial and wall-mounted units for stores and smaller rooms.
- Ceiling-mounted units where floor space is valuable.
- Ducted units that distribute dry air through ductwork to large or multiple spaces, or integrate with an AHU.
- Desiccant rotor units for low dew points and low temperatures.
We supply AirMax dehumidifiers as technology partner and authorised distributor, across portable, commercial, ducted, ceiling-mounted, swimming pool, desiccant rotor and low-temperature models. Browse the dehumidifiers category.
Special duties: cold stores and swimming pools
Low-temperature spaces
Cold stores, chilled production rooms and their loading docks have a particular problem. Warm, humid outdoor air entering through doors meets cold surfaces and cold air. Water condenses on walls and ceilings, forms frost on evaporator coils, and turns to ice on floors and doors. The results are slip hazards, more frequent defrost cycles, frost on product and packaging, and dripping inside the store.
Refrigerant dehumidifiers struggle at these temperatures, which is why desiccant units and dedicated low-temperature models are used. The biggest gains often come from the building side: fast-acting doors, strip curtains, dock seals and a dehumidified anteroom or dock area that buffers the store from outdoor air.
Swimming pools and other open water
Indoor pools, water treatment halls and wash areas evaporate large quantities of water from open surfaces. The evaporation rate depends on water temperature, air temperature and humidity, surface area and activity; the ASHRAE Handbook (HVAC Applications) gives a method for estimating it. Without enough dehumidification, the building suffers condensation, corrosion of structural steel and fittings, and mould.
Pool dehumidifiers are designed for this load and usually recover the heat from the dehumidification process into the pool water or the room air. The building envelope matters as much as the unit: vapour barriers and surface temperatures must be designed so the room air’s dew point does not meet a cold surface.
Sizing logic: build the moisture load, then choose the machine
The most common sizing error is choosing a dehumidifier from room volume. Volume tells you almost nothing. Two warehouses of the same size can have moisture loads that differ by a large factor, because one has a dock door open all day and the other has a single sealed entrance.
Sizing is a mass balance. Water enters the space from several sources. The dehumidifier must remove it at the same rate, while holding the target condition. The method below is qualitative on purpose: the numbers come from your site, your building and recognised references such as the ASHRAE Handbook and ASHRAE’s Humidity Control Design Guide, not from a single rule of thumb.
Step 1: set the target condition as a dew point
Start from the product or process requirement. A product specification usually states an RH and a temperature, for example “not above 45% RH at 25 °C”. Convert that to a dew point or humidity ratio. That becomes the design target, and it stays valid if room temperature drifts.
Ask where the limit applies. If it applies at the product, the condition must be held at the product, which may be next to a wall, inside a carton or under a ceiling, not at the sensor in the centre of the room.
Step 2: choose the outdoor design condition
Many cooling designs are based on peak dry-bulb temperature. For dehumidification, the worst case is the most humid weather, which is not always the hottest. ASHRAE publishes climatic design data that include dehumidification design conditions, expressed as a dew point with its matching humidity ratio, for weather stations worldwide. Use them, or reliable local weather records, for your site. In much of Southeast Asia, outdoor dew points stay high for most of the year, and the monsoon raises them further.
Step 3: list every moisture source
| Moisture source | What drives it | How to reduce it |
|---|---|---|
| Fresh (ventilation) air | Airflow and the difference in humidity ratio between outdoor and room air | Pre-dry fresh air at the AHU, use only the ventilation required |
| Infiltration | Door openings, gaps, cracks, unsealed penetrations, pressure differences | Seal the envelope, fast doors, airlocks, slight positive pressure |
| People | Number of people and activity level | Count people realistically per shift |
| Product and packaging | Moisture released by wet product or packaging entering the space | Condition materials before entry, separate wet processes |
| Open water and wet processes | Evaporation from tanks, washing, wet cleaning | Covers, local extraction, scheduled cleaning |
| Building envelope | Vapour diffusion through walls, roofs and floors | Vapour barriers on the warm side |
For each source, the estimate needs inputs you can defend:
- Fresh air: mass flow of air multiplied by the difference in humidity ratio between the outdoor design condition and the room target.
- Infiltration: estimated airflow through openings and gaps, multiplied by the same humidity ratio difference. Door openings are often the largest single load in warehouses and loading areas, and the hardest to estimate. Measure or log door activity if you can.
- People: moisture released per person by activity, from the latent heat gains published in the ASHRAE Handbook (Fundamentals).
- Product: the difference in moisture content between incoming material and its equilibrium content in the dry room, multiplied by throughput. The product data or a simple drying test provides it.
- Open water: an evaporation estimate from recognised references, or a measurement.
Step 4: a worked example for fresh air
Fresh air is usually the easiest load to calculate, and often the largest in production spaces. Using the conditions from the psychrometrics section:
- Outdoor design: 32 °C, 75% RH, about 22.7 g/kg.
- Room target: 24 °C, 50% RH, about 9.3 g/kg.
- Difference: about 13.4 g of water per kg of air.
- 1,000 m³/h of outdoor air weighs roughly 1,140 kg at that condition.
So 1,000 m³/h of fresh air brings in roughly 15 kg of water per hour that must be removed before or after it reaches the room. Running around the clock, that is in the order of 370 kg a day, from one modest ventilation airflow. This is an illustrative calculation from physical properties; your design uses your airflow and your climate data.
Step 5: from load to machine
With the total moisture load in kg/h, the selection follows:
- Capacity at your design condition. Dehumidifier capacity is quoted in litres or kilograms per day at a stated air temperature and RH, and different manufacturers use different rating conditions. Ask for capacity at your inlet condition, not the catalogue headline.
- Supply dryness and airflow. The unit’s supply air must be drier than the room target, and the airflow must be enough to carry the load away at that dryness difference.
- Distribution. Dry air must reach where the product is. Ducted supply and return, or several smaller units, may hold the condition more evenly than one large unit in a corner.
- Margin and redundancy. Allow for load uncertainty and decide what happens when one unit is down for service.
- Heat. Account for the heat the dehumidifier adds and remove it with cooling if temperature matters.
Air conditioning and dehumidification are different jobs
A conventional air-conditioning system is controlled by temperature. It removes moisture only as a by-product, when its coil happens to be below the dew point. In humid weather with low sensible load, such as an overcast monsoon day with the doors open, the thermostat is satisfied long before enough water has been removed, and RH climbs. Oversized cooling equipment that cycles on and off makes this worse.
The fix is to separate the two jobs: treat the fresh air for moisture at the air-handling unit, control humidity on its own sensor, and let cooling handle temperature. Our HVAC and cooling solutions and the Nexus range of HVAC and chillers integrate with dehumidification for this reason. Capacities selected to your load. Ask for a datasheet.
Build the room around the dehumidifier
A dehumidifier cannot dry the outdoors. Before adding capacity, make the space worth drying:
- Seal the envelope. Gaps around doors, roof sheets, cable and pipe penetrations, and unsealed block walls let humid air in continuously.
- Add a vapour barrier on the warm (outer) side of walls and roofs of dry rooms and cold spaces.
- Control doors. Fast-acting doors, strip curtains and airlocks reduce infiltration. A small dehumidified anteroom is often cheaper than more capacity in the main room.
- Keep the space slightly pressurised. Supplying a little more dry air than is extracted pushes air out through gaps instead of drawing humid air in. Positive pressure also matters in clean rooms, as our air quality guide explains.
- Separate wet processes. Wash areas, open tanks and steam sources belong outside the dry zone, or under local extraction.
Applications across Southeast Asian industry
| Industry | What humidity damages | Typical approach |
|---|---|---|
| Garment and textile | Mould on finished goods, softened cartons, odour | Dehumidified finished-goods stores, sealed packing areas |
| Pharmaceutical | Hygroscopic powders, tablets, capsules, packaging | Dry rooms to a product-derived dew point, often desiccant |
| Food and beverage | Caking powders, sticky confectionery, condensation, frost | Dry packing rooms, dehumidified docks and anterooms |
| Warehousing and logistics | Mould, corrosion, carton strength, labels | Envelope sealing plus refrigerant or ducted units |
| Electronics | Moisture absorbed by components and boards | Controlled storage and assembly areas |
Garment and textile
Garment plants handle a hygroscopic product in a humid climate. Cotton and blended fabrics absorb moisture from the air, and finished garments packed into cartons can develop mould and odour in storage or in transit if they were packed damp. Corrugated cartons also lose strength as they absorb moisture.
Sewing floors are often cooled by ventilation or evaporative cooling for worker comfort, which adds moisture to the air. That is fine on the sewing floor. The places that need humidity control are the finished-goods store, the packing area and the fabric store. Treat them as separate zones, seal them, and control them on dew point. Read industrial dehumidifiers for garment factories and warehouses in humid climates and see our garment and textile page.
Pharmaceutical and healthcare
Many active ingredients and excipients are hygroscopic. Effervescent products, gelatin capsules and some powders are particularly sensitive. The limit for a given room comes from the product’s stability and process data, not from a generic table, and it should be written into the room specification with the tolerance and the monitoring point.
Dry rooms for these products often need dew points that refrigerant coils cannot reach, so desiccant rotors are common, combined with cooling and HEPA filtration in a clean-room air system. Humidity control in a GMP area also has to be qualified and monitored, so sensor calibration and records are part of the design. See humidity control in pharmaceutical and food production and pharmaceutical and healthcare.
Food and beverage
Dry ingredients such as sugar, milk powder, flavourings and instant beverages cake when they absorb moisture. Confectionery and biscuits become sticky or soft. Packaging seals and labels suffer. In chilled and frozen operations the problem is condensation and frost: dripping ceilings over open product, ice on dock floors, and evaporators that need constant defrosting.
The usual answers are dry packing rooms, dehumidified loading docks and anterooms in front of cold stores, and dew-point control in areas where cold surfaces meet humid air. Visit food and beverage.
Warehousing and logistics
In a general warehouse the targets are usually modest, often to keep RH below the level where mould grows and corrosion accelerates, but the volumes are large and the doors are open. Refrigerant or ducted dehumidifiers work well here, once the envelope is sealed and the dock areas are managed. Products that need tighter control, such as metal parts, paper, electronics or pharmaceuticals, are often grouped into a smaller controlled zone instead of drying the whole building. See warehousing and logistics.
Electronics
Many surface-mount components absorb moisture from the air. During reflow soldering, that moisture can expand rapidly and crack the package or delaminate it internally. The industry standard for handling these parts is IPC/JEDEC J-STD-033, which defines moisture sensitivity levels, how long parts can be exposed to the shop floor once removed from dry packing, and how to dry them. Controlled storage, dry cabinets and humidity-controlled assembly areas help keep exposure within those limits. Electronic assembly also needs attention to static, which is why very dry air is not the goal either. See electronics.
Control and monitoring
Control on the right variable
Most dehumidifiers ship with an RH humidistat. That is adequate in a space with stable temperature. Where temperature varies, controlling on RH can make the system chase temperature changes rather than moisture. Controlling on dew point or humidity ratio, calculated from a combined temperature and humidity sensor, gives steadier results.
Put sensors where the risk is
- At least one sensor representative of the product zone, away from the dehumidifier’s supply air stream and away from doors.
- Additional sensors at known risk points: near doors, at cold walls, at high racking levels.
- An outdoor sensor, so the system’s performance can be judged against the weather.
Calibrate and trend
Capacitive humidity sensors drift over time, especially in dusty or chemically contaminated air. A sensor that reads a few percent low will let the room run wetter than intended without anyone noticing. Schedule calibration checks against a reference instrument and keep the records, particularly in regulated areas.
Trending is what turns a dehumidifier into a managed system. With humidity, temperature, unit status and energy logged, you can see whether a complaint coincides with a door left open, a failed unit or a weather event. Nexus AirSight collects these signals with other plant utilities on one screen, with alarms, history and reports, through a PLC and SCADA layer.
Maintenance that keeps the dew point where you set it
A dehumidifier that is not maintained loses capacity gradually. The room drifts wetter, and the first sign is often damaged product.
| Component | What to check | Why it matters |
|---|---|---|
| Air filters | Condition, differential pressure, replacement | Clogged filters cut airflow and capacity; in desiccant units they protect the rotor |
| Coils (refrigerant units) | Cleanliness, fin condition | Dirty coils reduce heat transfer and water removal |
| Condensate drains and pumps | Free flow, traps, algae, pump function | Blocked drains overflow or re-evaporate water into the room |
| Refrigerant circuit | Pressures, temperatures, leak checks | Low charge reduces capacity and efficiency |
| Desiccant rotor | Face condition, seals, drive belt or motor, rotation | Leaking seals and a stopped rotor cut performance |
| Regeneration heater and airflow | Heater output, reactivation airflow, outlet temperature | Insufficient regeneration leaves the desiccant wet |
| Fans and motors | Bearings, belts, current | Airflow is capacity |
| Sensors and controls | Calibration, set-points, alarm function | Wrong readings mean wrong control |
Follow the manufacturer’s intervals and adjust for dust and operating hours. In dusty environments such as garment and agro-processing plants, filter changes come round faster than the manual suggests. Filter elements and media are in our filters and media range, and parts are covered by our spare parts service. A maintenance contract puts these checks on a schedule with records.
For systems that combine dehumidification with cooling, chiller and AHU maintenance matter as much as the dehumidifier itself. Our chiller maintenance checklist for hot climates covers that side.
Scoping a dehumidification project
Most dehumidification projects that disappoint failed at the scoping stage: the target was stated in RH without a temperature, the loads were guessed from volume, or the building leaked more than anyone expected. A good scope answers these questions before equipment is chosen.
What we need to design a dehumidification system
- What damage are you preventing, and at what condition does it start?
- Target condition: temperature and RH, or dew point, with tolerance
- Where the condition must be held: room average, product zone or specific points
- Room dimensions, construction and the condition of the envelope
- Doors: number, size, type and how often they open per shift
- Fresh air: how much is supplied today and why
- People per shift and their activity
- Product and packaging entering the space, and their moisture condition
- Open water, washing or wet processes in or near the space
- Existing cooling or air-handling equipment
- Available power and regeneration heat sources
- Monitoring and records required, including any GMP or customer requirements
From that brief, the design sequence is the same as for any utility: survey and data logging where the space already exists, moisture load calculation, technology selection, equipment and duct design, control and monitoring design, installation, commissioning against the target condition, and handover with a maintenance plan. Our humidity control solution covers the full scope, from design and engineering to installation and commissioning.
Savings are project-specific. We measure them against a baseline and verify them after implementation; we don’t promise a blanket percentage. In dehumidification, the most useful baseline is often not energy but product loss: rejected batches, claims and stock written off before and after.
Where to go next
- Equipment: dehumidifiers, HVAC and chillers, filters and media.
- Solutions: humidity control, HVAC and cooling, SCADA and monitoring.
- Articles: dehumidifiers for garment factories and warehouses, humidity control in pharma and food, clean rooms and positive pressure.
- Tools and resources: system selector, unit converter, and the dehumidification project brief template in our resources.
- Related guides: compressed air and industrial air quality.
If you have a room that sweats, a product that cakes or a store that smells of mould, send us the brief above. Request a quote or contact the engineering team.