Phnom Penh, serving Cambodia and the region

Solution

Compressed air designed as one system, not a pile of machines

Compressed air system design at Nexus Turnkey covers the whole chain: generation, treatment, storage and condensate, distribution, power and automation, and the compressor room itself. We size each package from your measured or projected demand, treat air only to the ISO 8573-1 class your process needs, build in N+1 redundancy where downtime is costly, and ventilate the room for tropical heat. One team designs, supplies, installs, commissions and supports it, so one team answers for pressure, air quality and energy.

Process pipework with valves and fittings in an industrial plant room

Anatomy of an air system

Six packages. One accountable hall.

A compressor room is a system, not a machine. We engineer it package by package, and each package answers a different question.

  1. Package 1 of 6

    Generation

    Oil-injected screw compressors in fixed-speed, VSD or PM-VSD form, oil-free machines where the process demands it, diesel portables and high-pressure packages.

    Design prioritySized to the measured demand profile, with duty and standby defined, delivery verified and package power known.

    Air compressors
  2. Package 2 of 6

    Treatment

    Aftercooling and separation, refrigerated or adsorption dryers, then particulate, coalescing and carbon filtration.

    Design priorityThe pressure dew point and the particle and oil limits your process needs, with capacity corrected to site conditions rather than catalogue ones.

    Air treatment
  3. Package 3 of 6

    Storage & condensate

    Rated receivers with their safety accessories, automatic drains and oil-water separators.

    Design priorityRide through transient demand, hold pressure steady, keep maintenance safe and keep condensate under control.

    Air treatment and condensate
  4. Package 4 of 6

    Distribution

    Ring mains, headers and drops to each machine, with isolation valves, supports and allowance for expansion.

    Design priorityLow pressure loss, the right pipe material, access for maintenance and room to expand in phases.

    Treatment and distribution
  5. Package 5 of 6

    Power & automation

    Panels, protection, cabling, metering, PLCs, sequencing and the interface to SCADA.

    Design prioritySafe integration, coordinated control and data your team can actually use.

    SCADA and monitoring
  6. Package 6 of 6

    Compressor room

    Layout, ventilation and heat ducting, access, drainage and the interfaces to other utilities.

    Design priorityNo hot-air recirculation, and space to maintain, lift and install.

    Compressed air systems
Isometric drawing of a compressor hall: three screw compressors, aftercooler, dryer and filters, an air receiver with drains and an oil-water separator, a ring main leaving the room, a control panel with cable tray, and the room's louvres and hot-air ducts.C1C2C3PTFTATkWPKG 01 · GENERATIONPKG 02 · TREATMENTPKG 03PKG 04 · RING MAINPKG 05PKG 06 · COMPRESSOR ROOM
Fig. 01 · Compressor hall, isometric Airflow

Where compressed air systems go wrong

Most plants did not design their compressed air system. They accumulated it. A compressor bought with the first production line, a second one added when pressure dropped, a dryer from another supplier, piping laid by whoever was on site that month. Each purchase made sense on its own. Together they rarely do.

The symptoms are familiar. Pressure sags at the far end of the building, so someone raises the setpoint and every compressor works harder. Water appears in the lines during the monsoon. Two machines run part-loaded when one would do. The compressor room is hot enough that machines trip in the afternoon. Nobody can say what a cubic metre of air costs, because nobody measures it.

The root cause is the same in almost every case. Nobody owned the system as a whole. Compressors, treatment, storage, piping and controls were treated as separate purchases, so problems fall between scopes and no one is answerable for the result.

A compressor is a component. Compressed air is a system, and it should be designed as one.

Our approach: start from demand, design the whole chain

We start with the air your plant actually uses, not the machine you think you need. For an existing site that means measuring it. For a new factory it means building a demand model from the equipment list: each consumer’s flow and pressure, how many run at the same time and for how long, and where the plant is likely to grow.

From there we design six packages as one system.

Generation is sized around the demand profile, not the peak alone. A hall usually needs a base-load machine that runs fully loaded most of the time, and a trim compressor, often a VSD or PM-VSD unit, that follows the swings. We compare fixed-speed and variable-speed options on lifetime energy cost, not purchase price alone. We supply Ingersoll Rand and Sollant compressors as an authorised distributor, and we select between them on the duty, not the brand.

Treatment is specified to the air quality the point of use requires. We express that requirement as an ISO 8573-1 class for particles, water and oil. Over-treating wastes energy in pressure drop and purge air. Under-treating damages product and machines. Dryers and filters are then sized with the manufacturer’s correction factors for your inlet temperature, ambient and pressure, not at catalogue reference conditions.

Storage and condensate stabilise the system. Correctly sized receivers absorb short demand peaks so compressors do not cycle unnecessarily. Zero-loss drains remove condensate without blowing off compressed air, and an oil-water separator treats it before discharge.

Distribution delivers the pressure you generate to the machines that use it. A looped ring main sized for low pressure drop, drops taken from the top of the header, falls towards drain points and isolation for each zone. Getting this right is what lets you run the whole hall at a lower setpoint.

Power and automation tie it together: protection, metering, a sequencer or PLC so the compressors work as one hall, and interfaces to SCADA if you want the data on a screen. Our AirSight monitoring builds on this layer.

The compressor room is designed, not left over. Layout for access and lifting, ventilation and hot-air ducting, drainage and utility connections.

Greenfield, brownfield and digital

We work in three situations, and the method adapts to each.

  • Greenfield. A new factory or a new building. We size the room for today’s load and tomorrow’s expansion, so you can add a compressor without moving walls or re-piping.
  • Brownfield. An existing plant that needs more capacity, better air quality or a lower energy bill. We replace, re-pipe, correct leaks and retrofit controls in stages, without stopping production. See plant renovation.
  • Digital integration. The equipment is sound but nobody can see it. We add multi-compressor sequencing, PLC integration and a SCADA overlay so the hall reports one energy number.

Uptime by design: N+1

If a stopped compressor stops production, the hall needs N+1 capacity. That means peak demand can still be met with the largest machine out of service. We decide where redundancy is worth paying for, and where a temporary-air plan is a better answer. The standby machine is integrated into the sequence so it shares running hours instead of sitting idle for years.

Designing for tropical heat

Cambodia’s climate is hard on compressed air. High ambient temperatures and humidity run all year, with the heaviest moisture loads in the wet season.

That same heat can be an asset. Where a plant needs hot water, heat recovery from the compressors is often worth evaluating. We cover that under energy optimisation.

How this fits with the rest of your plant

Compressed air rarely stands alone. Nitrogen generators depend on clean, dry feed air, so we design the two together when you need nitrogen. Dehumidification, cooling and emissions control often share the same plant rooms, power and controls. Being responsible for every kind of air on the site means we can plan those interfaces once.

The work is delivered through our services. An air audit establishes the baseline on existing plants. Design and engineering produces the P&IDs, layouts and calculations you approve. Installation and commissioning builds and proves it. Maintenance contracts keep it performing.

Standards we work to

Use the ISO 8573-1 class explorer to see what each class means, or the compressed air cost calculator to estimate what your current system costs to run.

Scope

What's included

The six packages of a complete compressed air system
PackageWhat it coversWhat we design for
1. GenerationOil-injected rotary screw compressors (fixed speed, VSD, PM-VSD), oil-free machines where the process demands them, diesel portables and high-pressure packagesYour demand profile, duty and standby roles, verified delivered flow and total package power
2. TreatmentAftercoolers and separators, refrigerated or desiccant dryers, particulate, coalescing and activated-carbon filtrationThe pressure dew point and particle and oil limits you actually need, with capacity corrected to site conditions
3. Storage and condensateRated air receivers with safety accessories, automatic drains, oil-water separatorsBuffering of transient demand, stable pressure, safe maintenance and controlled condensate discharge
4. DistributionRing mains, headers, drops to machines, isolation points, supports and expansion allowanceLow pressure loss, suitable materials, access for maintenance and room for phased growth
5. Power and automationPanels, protection, cabling, energy metering, PLCs, multi-compressor sequencing and SCADA interfacesSafe electrical integration, coordinated control and data you can actually use
6. Compressor roomLayout, ventilation and hot-air ducting, access, drainage and utility connectionsNo recirculation of hot air, and space to maintain, lift out and add machines

FAQ

Questions engineers ask us

What does a turnkey compressed air system include?

Everything between the incoming power supply and the air at your machines: compressors, dryers and filters, receivers and condensate handling, the ring main and drops, electrical panels and controls, and the compressor room layout and ventilation. We also commission it, train your operators and hand over full documentation.

How do you size compressors for a new factory with no operating history?

We build a demand estimate from the equipment list: each consumer's air requirement, its pressure, how many run at once and for how long. We then add a reasoned allowance for growth and select machines so that the base load runs efficiently today and capacity can be added later without rebuilding the room.

Do we need oil-free compressors?

Not always. The question is what air quality the point of use requires, expressed as an ISO 8573-1 class. Some processes in food, pharmaceutical and electronics manufacturing justify oil-free compression. Many others are well served by oil-injected compressors with the right filtration. We explain the trade-off for your application before you commit.

What does N+1 mean for a compressor hall?

It means the hall can still meet peak demand with its largest machine out of service. One extra unit, sized and controlled correctly, lets you maintain or repair a compressor without stopping production.

Why does compressor room ventilation matter so much in Cambodia?

Compressors reject almost all of the electrical energy they consume as heat. In a hot climate, a poorly ventilated room recirculates that heat, raises the intake temperature, reduces delivered air and can trip machines on high temperature. We design ducting and airflow so hot air leaves the room and cooler air feeds the compressors.

Can you extend or upgrade an existing system rather than replace it?

Yes. Brownfield work is a large part of what we do. Machines with useful life can stay on as peak or standby units under a new control overlay. See our plant renovation approach for how we stage changes without stopping production.

Next step

Plan your compressor hall with one accountable team

Share your equipment list or current setup. We will come back with a scoped approach for generation, treatment, distribution and controls.

Start typing to search