Phnom Penh, serving Cambodia and the region

Industry

Dry instrument air, inert nitrogen and a clean stack

Air and emissions systems for chemical plants have to keep instruments working, keep flammable atmospheres inert and keep acid gases, VOCs and odours inside the permit. Nexus Turnkey designs dry, reliable instrument and process air with standby capacity, on-site nitrogen for blanketing and purging, and scrubbers, carbon or thermal treatment for the exhaust. Process cooling and monitoring complete the utility. Equipment in classified areas is selected for the zone your hazardous-area study defines.

Chemical plant with storage tanks and process columns at dusk
Factory cross-section highlighting the air services used in Chemicals: Compressed air, Air treatment, Nitrogen, Emissions control, HVAC & chillers, Monitoring (AirSight). PRODUCTION HALLN₂+
Fig. · Factory cross-section, air services

Chemicals

Air and emissions for chemical plants

A chemical plant relies on air for control and safety. The lens shows dry instrument air with standby, nitrogen blanketing tanks and purging lines, scrubbers and VOC treatment on the exhaust, cooling on the process, and monitoring that alarms before a utility failure becomes a process upset.

Air services in focus: Compressed air, Air treatment, Nitrogen, Emissions control, HVAC & chillers, Monitoring (AirSight).

Explore chemicals

The challenge

Chemical plants depend on air for control and safety, not just production. Instrument air drives control loops, so a wet or failed supply can upset the process. Nitrogen keeps flammable vapours below their limits in tanks and reactors. Exhaust from reactors, tank vents and scrubber stacks carries acid gases, solvents and odours that the permit limits. A hot, humid climate makes instrument air harder to keep dry and puts cooling systems under load.

The air services a chemical plant needs

Instrument and process air is designed with N+1 generation and dryers. A desiccant dryer is used where lines are exposed or cooled, and receivers give safe hold-up time. See compressed air systems and air treatment.

Nitrogen comes from a PSA generator for blanketing, purging and inerting, with an oxygen analyser and alarm. See nitrogen generators.

For emissions, a packed-bed scrubber handles acid and alkaline gases and a venturi scrubber handles fumes and mists. Activated carbon or an RTO treats VOCs. See air quality and emissions and our VOC treatment comparison.

Process cooling comes from chillers and cooling towers, with standby where the process cannot lose cooling.

Monitoring brings dew point, nitrogen purity, scrubber differential pressure and pH, and stack readings onto one screen. See SCADA and monitoring.

What we check first

Utility failures in chemical plants tend to come from single points that nobody noticed. Our survey looks for them.

  • Dew point against the coldest point. In a tropical plant the coldest lines are often in air-conditioned rooms or near chilled process equipment. Instrument air must stay dry there, not just at the dryer outlet.
  • Single points of failure. One dryer, one receiver or one power feed serving all instrument air is a risk the process safety study should see.
  • Nitrogen use and purity. Purge and blanketing demand is often intermittent, with high peaks. We log it and confirm the purity the process actually needs before sizing a generator.
  • Scrubber condition. Liquor pH, recirculation flow, packing condition and differential pressure show whether a scrubber still performs as designed.

Findings go into a ranked list with the measurement and the risk behind each one.

Standards and limits

Typical scope

PackageWhat it usually includes
Instrument airN+1 compressors and dryers, receivers, dew-point alarm
NitrogenPSA generator, buffer, analyser, distribution
ExhaustScrubbers, carbon or thermal treatment, fans, stack
Cooling and monitoringChillers, cooling towers, utility SCADA

Our design and engineering team works from your process data and hazardous-area drawings.

Scope

Relevant standards

Standards that commonly shape this industry's air
StandardWhy it matters here
ISO 8573-1:2010Purity classes for compressed air. Instrument air needs a dew point well below the lowest temperature its lines will see.
IEC 60079 seriesHazardous-area classification and equipment protection. Equipment in a classified zone must suit that zone.
Environmental permit limitsLimits for acid gases, VOCs and odour come from your permit. We design treatment to meet them.
We design to the standard your process requires. Nexus describes these standards; it does not claim certification against them.

FAQ

Questions engineers ask us

Which scrubber suits our exhaust?

Packed-bed scrubbers suit soluble acid and alkaline gases such as HCl and ammonia. Venturi scrubbers suit particulates, mists and fumes. Odour and VOCs may need carbon or thermal treatment. The gas composition, flow and temperature decide.

How much standby should instrument air have?

Enough that losing any one compressor or dryer does not starve the instruments, which usually means N+1, plus a receiver sized to give safe shutdown time if supply fails. Your process safety study sets the hold-up time.

Should we make nitrogen on site?

If you blanket tanks or purge lines daily, a PSA generator often replaces cylinders or liquid deliveries. We size it to peak purge demand and add an oxygen analyser and alarm.

Next step

Make instrument air and nitrogen the dependable part

Share your utility list and hazardous-area drawings. We will design instrument air, nitrogen and exhaust treatment to suit.

Start typing to search