Phnom Penh, serving Cambodia and the region

Compressed air

Oil-Free vs Oil-Injected Compressors for Food, Beverage and Pharma

Oil-free or oil-injected? Where the oil risk sits in each design, what ISO 8573-1 Class 0 really means, and how food, beverage and pharma plants should decide.

Nexus Turnkey Engineering Team6 min read

The difference is where the oil risk sits

Both oil-free and oil-injected compressors can supply air that meets food, beverage and pharmaceutical requirements. The difference is where the risk sits. An oil-injected screw compressor puts oil into the compression chamber and relies on separators and filters to take it out again. An oil-free compressor keeps lubricant out of the compression chamber, so the compressor itself cannot add oil to the air. Choose oil-free where your risk assessment says any compressor oil carryover is unacceptable. Choose oil-injected with a proven treatment train where it is not. Either way, define the ISO 8573-1 class first.

This article explains how each design works, what the standards ask for and how to decide. It is part of our industrial compressed air guide.

How each design handles oil

Oil-injected screw

In an oil-injected rotary screw compressor, oil is injected into the airend. It seals the clearances between the rotors, carries away heat of compression and lubricates bearings. After compression, a separator removes most of the oil and returns it to the circuit. A small amount remains in the air as aerosol and vapour.

Downstream treatment removes that remainder. A coalescing filter captures oil aerosol. An activated carbon stage adsorbs oil vapour when a strict oil class is needed. Done properly, this reaches very low oil levels. The risk is in maintenance: a saturated filter element, a failed separator or a bypass left open can let oil through.

Food plants often run oil-injected compressors on lubricants registered for incidental food contact, such as NSF H1 grades. That reduces the consequence of a carryover event. It does not remove the need for filtration or for testing.

Oil-free

Oil-free compressors keep lubricant out of the compression chamber. Common designs include dry screw machines, usually with two-stage compression and intercooling, water-injected screws and scroll compressors. Bearings and gears are still lubricated, but sealed from the air path.

The benefit is that no compressor lubricant can enter the air, even if something fails. The limits are just as real. Intake air carries hydrocarbons and particles from vehicles, generators, solvents and the plant itself, and these pass through any compressor. Water, particles and microbes still need treatment. Oil-free is a way of removing one risk, not all of them.

What the standards and guidance ask for

ISO 8573-1 sets the classes. Other documents say which class an application needs. For food and beverage, the British Compressed Air Society’s food-grade compressed air guideline recommends:

UseISO 8573-1:2010 classWhat that means
Direct contact with food2.2.1Particles Class 2, pressure dew point -40 °C or below, total oil 0.01 mg/m³ or below
Indirect contact with food2.4.2Particles Class 2, pressure dew point +3 °C or below, total oil 0.1 mg/m³ or below

The same guideline recommends testing compressed air purity at least twice a year, unless the HACCP process sets another frequency.

For pharmaceutical production, the requirement comes from your own quality system. Air that contacts product or primary packaging is treated as a process utility: its quality is specified, qualified and monitored. The class is a decision for your quality team and process owners. The compressor and treatment are then chosen to meet it with margin.

Define the air class first. The compressor technology follows from the risk, not from habit.

The two side by side

Oil-injected screw + treatmentOil-free compressor + treatment
Source of oil in the airCompressor lubricant plus intake hydrocarbonsIntake hydrocarbons only
How strict oil classes are reachedSeparator, coalescing filters, activated carbonFiltration as needed for intake contaminants
Failure riskOil carryover if separator or filters fail or are neglectedNo compressor lubricant in the air path
CondensateOily; needs an oil-water separator before dischargeNormally free of compressor oil; check local discharge rules
Maintenance focusFilter changes, separator, oil analysisAirend condition, cooling, intake filtration

How to decide

Work through these questions with your quality and engineering teams.

Oil-free or oil-injected?

  • Which ISO 8573-1 class does each point of use require?
  • Does the air contact product, primary packaging or a sterile process?
  • What would an oil carryover event cost: product recall, line clean-down, audit finding?
  • Can the plant maintain a strict filtration train reliably, with records?
  • How will air quality be tested, and how often?
  • What specific power does each candidate deliver at your pressure and flow?
  • How much pressure drop does each treatment train add?

Often the answer is mixed. A plant may run an oil-free compressor for product-contact air and an oil-injected one for general plant air, on separate systems. Or it may run oil-injected compressors throughout, with a strict treatment train on the branch that feeds the filling line. Both can be correct.

On energy, compare published specific power at your working point, not general claims. Include the pressure drop of the filters each option needs, because that is paid for in compressor power every hour. Our compressed air cost calculator helps compare the annual figures.

Test the air you have

A class on a specification is a promise. A test is the proof. The ISO 8573 series includes separate parts with test methods for each contaminant: particles, humidity, oil aerosol, oil vapour and microbiological contamination among them. Testing to those methods shows whether the air at the point of use actually meets the class you specified.

Three practical points make testing meaningful:

  • Test where the air is used. Air leaving the compressor room can be clean while air at a filling head is not, because of old pipework, a bypass left open or a saturated point-of-use filter.
  • Test on a schedule. A one-off test proves one day. The BCAS food-grade guideline recommends testing at least twice a year unless the HACCP process sets another frequency.
  • Test after changes. A new compressor, a filter change, a pipe modification or an oil carryover event are all reasons to test again.

For oil-injected systems, keep filter differential pressure and element change records alongside the test results. For oil-free systems, keep intake filter and cooling records. Either way, an auditor will ask for evidence, not a brochure.

Tropical points to check

Heat and humidity affect both designs. Oil-free dry screw compressors run hot internally and depend on effective intercooling and aftercooling, so room ventilation and cooling-water quality need attention. Oil-injected compressors in hot rooms run hotter oil, which shortens oil life. In both cases, the treatment train must be sized for hot, humid inlet air, as explained in our article on refrigerated vs desiccant dryers.

Whichever you choose, the energy comparison should rest on measured data. Savings are project-specific. We measure them against a baseline and verify them after implementation; we don’t promise a blanket percentage.

Getting the specification right

Start with the class, the risk and the test plan. Then look at machines. We supply oil-free and oil-injected air compressors from Ingersoll Rand and Sollant as an authorised distributor, together with the air treatment that goes with them. Ask us which series are currently supplied in Cambodia. For sector context, see how we approach food and beverage and pharmaceutical and healthcare plants. Then send us your required class and an engineer will set out both options side by side.

Nexus Turnkey Engineering Team

Written and reviewed by the engineers who design, install and maintain industrial air systems for Nexus Turnkey in Cambodia. Questions about this article? Ask us directly.

FAQ

Questions engineers ask us

Does an oil-free compressor deliver oil-free air?

It removes the compressor's own lubricant from the compression chamber, so no compressor oil can be carried into the air. But intake air can contain hydrocarbons from traffic, generators and the plant itself, and these pass through any compressor. Oil-free compressors still need appropriate filtration and drying to reach a strict ISO 8573-1 oil class.

Can an oil-injected compressor be used in a food factory?

Yes, where the risk assessment allows it and the treatment train reliably meets the required ISO 8573-1 class. The British Compressed Air Society's food-grade guideline recommends Class 2.2.1 for direct contact with food. Oil-injected systems reach strict oil classes through coalescing and activated carbon filtration, which must be maintained and checked.

What does ISO 8573-1 Class 0 mean?

Class 0 is not a zero-oil class. ISO 8573-1:2010 defines it as a limit specified by the equipment user or supplier that is stricter than Class 1. A Class 0 claim only means something when the specified limit and the test conditions are stated.

Which type uses less energy?

It depends on the size, design and operating point. Compare the published specific power of each candidate at your working pressure and flow, and include the pressure drop and energy of the filtration and drying each one needs. A strict filtration train on an oil-injected machine adds pressure drop that has to be paid for.

Next step

Turn this into a plan for your plant.

Send us your situation and an engineer will reply with the questions that matter and a sensible next step.

Start typing to search