Phnom Penh, serving Cambodia and the region

HVAC & cooling

Chiller Maintenance Checklist for Factories in Hot Climates

Chiller maintenance checklist for hot, humid, dusty plants: daily logs, coil and tube cleaning, approach temperatures, refrigerant checks and cooling towers.

Nexus Turnkey Engineering Team6 min read

Hot climates punish neglected chillers

Chiller maintenance in a hot climate comes down to four habits. Log operating data every day and compare it with the commissioning baseline. Keep heat transfer surfaces clean: air-cooled condenser coils, water-cooled condenser tubes and evaporators. Treat cooling tower water properly. And have qualified technicians check refrigerant, compressors, electrics and controls on a fixed schedule.

High ambient temperature makes every one of those habits matter more. A chiller rejects heat to outdoor air or to a cooling tower. The hotter that outdoor air, the higher the condensing pressure and the harder the compressor works. Add dust and humidity, and small faults become trips in the hottest weeks. Below is a practical checklist by frequency, informed by ASHRAE/ACCA Standard 180, the US standard practice for inspecting and maintaining commercial building HVAC systems, adapted for Cambodian conditions.

Why heat, dust and humidity raise the stakes

Heat. The compressor’s work depends on the lift between evaporating and condensing temperatures. Hot ambient air raises the condensing temperature, which increases power per unit of cooling and reduces the chiller’s available capacity. Any extra fouling on the condenser adds to that penalty at exactly the time cooling demand peaks.

Dust. Road and construction dust, cotton lint in garment plants and process dust coat air-cooled condenser fins and block airflow.

Humidity. High humidity means cooling coils in the AHU handle a large latent load, removing water as well as heat. Condensate trays and drains must work, or water and microbial growth follow. Our industrial dehumidification guide explains latent load and how cooling coils remove moisture. Cooling towers in hot weather evaporate more water, concentrating minerals faster.

Power quality. Voltage dips and interruptions stress motors and drives and can cause repeated restarts. Log trips and their causes.

The cheapest kilowatt of cooling is the one a clean condenser does not waste.

The checklist by frequency

FrequencyWhat to doWho
DailyLog temperatures, pressures, amps, alarms; check for leaks and unusual noiseOperator
WeeklyInspect air-cooled coils; check cooling tower water level, basin and treatment dosingOperator
MonthlyReview approach temperatures against baseline; check strainers, condensate drains, belts and fansOperator and technician
QuarterlyRefrigerant leak check; electrical connections and controls; sensor checks; water treatment reviewTechnician
AnnuallyCondenser and evaporator tube inspection and cleaning; oil analysis where applicable; full performance reviewTechnician

Treat the table as a starting point. Your site conditions, the chiller manufacturer’s instructions and your running hours set the final intervals.

Daily: the log that catches problems early

  • Chilled water supply and return temperatures
  • Condenser water supply and return temperatures, or ambient temperature for air-cooled units
  • Evaporator and condenser refrigerant pressures or saturation temperatures
  • Compressor current and load percentage
  • Oil pressure and temperature where the chiller reports them
  • Alarms, trips and restarts since the last log
  • Unusual noise, vibration, leaks or oil stains

A paper log works. A digital one is better, because trends become visible without anyone adding up columns. Where a SCADA system or building management system is available, these readings can be collected automatically. See our SCADA and monitoring solutions.

Approach temperatures: the early warning

The evaporator approach is the difference between the chilled water leaving the evaporator and the refrigerant evaporating temperature. The condenser approach is the difference between the refrigerant condensing temperature and the water leaving the condenser. For air-cooled units, compare condensing temperature with ambient air.

A rising approach at similar load, compared with the commissioning baseline, points to fouled tubes, scale, low refrigerant charge, non-condensables or airflow problems. It is one of the most useful numbers on the log, and it costs nothing to calculate.

Air-cooled condensers

Inspect coils for dust, lint, leaves and bent fins. Clean with methods and chemicals the coil manufacturer approves, working from the clean side outwards to avoid driving dirt deeper. Check fan motors, blades and guards. Make sure nothing recirculates hot discharge air back into the coil intake: walls, new buildings or stacked equipment can create that problem after installation.

Water-cooled condensers and cooling towers

Condenser tubes scale and foul if water treatment slips. Inspect and clean tubes annually, or sooner if approach temperatures rise. On the tower, check fill, drift eliminators, nozzles, basin cleanliness, fan and gearbox.

Refrigerant and compressor

Leak checks, charge verification and any refrigerant handling belong to trained technicians with the right recovery equipment. Refrigerant is recovered, never vented. Older units charged with HCFC refrigerants such as R-22 face reducing supply as consumption is phased out under the Montreal Protocol, to which Cambodia is a party. If you run one, plan its future before a major leak forces the decision.

Oil analysis, where the compressor design allows, can reveal wear, moisture or acid before a failure.

Electrical and controls

Tighten and inspect connections, check contactors and starters or drives, and verify that sensors read correctly. A temperature sensor that drifts by a degree can push a chiller to run harder than necessary or to trip on a false alarm. Check set-points against the design intent.

Chilled water side

The chilled water loop needs care too. Clean strainers so the evaporator gets its design flow, and confirm that flow switches trip as they should, because a chiller running with low water flow risks freezing its evaporator. Treat closed loops against corrosion and keep records of water tests. Check pumps for seal leaks, bearing noise and vibration.

In a humid climate, pipe insulation matters more than it seems. Chilled water pipes run well below the dew point of the surrounding air. Damaged insulation or vapour barriers let moisture condense on the pipe, which drips, corrodes supports and soaks the insulation further. Inspect insulation along the whole route, especially at valves, hangers and pump connections, and repair it promptly.

Efficiency: measure it, don’t assume it

A chiller’s efficiency is described by COP or EER, the cooling delivered per unit of electrical input. Measuring it in service needs chilled water flow, temperature difference and electrical input. Even without full metering, the trend of power per unit of load and the approach temperatures show whether efficiency is drifting.

Clean coils and tubes, correct charge and accurate controls protect efficiency. Savings are project-specific. We measure them against a baseline and verify them after implementation; we don’t promise a blanket percentage.

Building the plan into a contract

Daily and weekly checks sit well with plant staff. Quarterly and annual work, refrigerant handling and diagnostics need specialist technicians. A maintenance contract that combines both, with clear reporting, is often the most reliable arrangement. Our article on what a good maintenance contract should include applies to chillers as much as compressors. The same heat that loads chillers loads compressor rooms too; see designing a compressor room for tropical heat.

Keep the cooling you paid for

A chiller that is logged, cleaned and checked on schedule keeps delivering the cooling it was selected for, even in the hottest weeks of the year. We supply chillers, AHUs and cooling towers in the Nexus range, with capacities selected to your load (ask for a datasheet), and spare parts for existing plant through our HVAC and chillers range. Our maintenance contracts cover the scheduled work, and the system selector is a quick first step if you are planning new cooling capacity.

Nexus Turnkey Engineering Team

Written and reviewed by the engineers who design, install and maintain industrial air systems for Nexus Turnkey in Cambodia. Questions about this article? Ask us directly.

FAQ

Questions engineers ask us

How often should chiller condenser coils be cleaned?

As often as your site conditions require. Dusty, lint-laden or polluted air fouls air-cooled condenser coils quickly. Inspect them regularly, clean when inspection or rising condensing pressure shows fouling, and log what you find so the interval reflects your plant rather than a generic schedule.

What is approach temperature and why does it matter?

Approach is the temperature difference between the refrigerant and the water leaving a heat exchanger. A rising approach, compared with the commissioning baseline at similar load, is one of the earliest signs of fouled tubes, low refrigerant charge or other heat transfer problems.

Do cooling towers need special attention?

Yes. Cooling towers need water treatment to control scale, corrosion and biological growth, including Legionella. ASHRAE Standard 188 sets out a risk management approach for building water systems that includes cooling towers.

Can our own staff maintain the chiller?

Trained in-house staff can handle daily logs, visual checks and basic cleaning. Refrigerant work, compressor and electrical diagnostics, and controls changes should be done by qualified technicians, often under a maintenance contract.

Next step

Turn this into a plan for your plant.

Send us your situation and an engineer will reply with the questions that matter and a sensible next step.

Start typing to search