Phnom Penh, serving Cambodia and the region

Compressed air

How to Choose the Right Air Compressor for Your Factory in Cambodia

Choose an air compressor by measured demand, lowest workable pressure, required air quality and Cambodia's heat, humidity and power, then lifecycle cost.

Nexus Turnkey Engineering Team6 min read

Start with five decisions, in order

To choose the right air compressor, decide five things before you look at a brochure. How much air you use, measured as free air delivery (FAD) over a real production week. The lowest pressure your machines need at the point of use. The air quality class your process requires. How demand swings across shifts, which decides the control type. And the site conditions the compressor must survive: in Cambodia that means heat, humidity, dust and variable power quality. Technology, size and number of machines follow from those answers. Lifecycle cost decides between the options that remain.

This article walks through each decision. For the full picture, from generation through treatment and distribution to control, see our industrial compressed air guide.

Measure demand, don’t add up nameplates

The most common sizing error is to total the air consumption of every machine on the floor and add a margin. Machines do not all run at once, and nameplate figures are maximums. The result is a compressor hall that is too big for the real load.

The better route is to measure. Log flow, pressure and compressor power for at least one full production week, including nights, weekends and changeovers. If you have no flow meter, an engineer can estimate delivered air from load and unload times and package power. A compressed air audit does this properly and gives you a baseline to judge the new plant against.

When you read the log, look for three things:

  • Base demand: the flow that never goes away during production.
  • Peaks: short events that a receiver can often cover instead of a larger compressor.
  • Off-production demand: air used when nothing is running. It is usually leaks. Fix it before you buy capacity for it.

Buy the compressor for the demand you have measured, not the demand you remember.

Set the lowest pressure that works

Pressure costs energy. The US Department of Energy’s compressed air sourcebook, written with the Compressed Air Challenge, gives a rule of thumb for systems around 100 psig (about 7 bar): every 2 psi (about 0.14 bar) of extra discharge pressure raises energy use by roughly 1 percent at full flow. Higher pressure also pushes more air through every leak and every unregulated use, which the same source calls artificial demand.

So find the machine that genuinely needs the highest pressure. Check whether it needs it everywhere or only at one point. Then add the realistic pressure drop across dryers, filters and piping. That is your discharge setpoint. If one process needs much more than the rest, a small dedicated booster or separate system may cost less to run than raising the whole plant. You can test the effect of a lower setpoint with our pressure reduction savings tool.

Define air quality before you choose the machine

ISO 8573-1 classifies compressed air purity by particles, water and oil. Write down the class each user needs. A general workshop line and a filling machine that blows into open bottles do not need the same air, and treating the whole plant to the strictest class wastes energy.

The required class decides two things. First, the dryer: a refrigerated dryer or a desiccant dryer. Second, whether an oil-injected compressor with filtration is acceptable or whether an oil-free compressor is the safer choice. Both decisions are covered in separate articles on dryers and oil-free versus oil-injected compressors.

Match the control to the demand profile

Once you know how demand swings, the control method follows. The table summarises the usual starting points. An engineer should still check them against your log.

Demand profileUsual approachWhy
Steady, near full load, long hoursFixed-speed rotary screwRuns at its most efficient point most of the time
Varies widely across the shiftVSD or PM-VSD compressorSpeed follows demand instead of loading and unloading
Large steady base plus a swingFixed-speed base load plus one variable-speed trim compressorEach machine does what it is good at
Several existing machinesA sequencer across the hallStops machines fighting each other and running unloaded

We compare the three drive types in detail in fixed speed vs VSD vs PM-VSD compressors.

Design for Cambodian site conditions

A compressor that performs well in a temperate showroom can struggle in a hot, humid, dusty plant room. Four site factors deserve attention in Cambodia.

Heat. Check the compressor’s maximum ambient temperature rating against the hottest day in the compressor room, not the average outdoor temperature. A poorly ventilated room can run well above outdoor ambient. Warm intake air is also less dense, so each cubic metre carries less mass of air. Our article on compressor room design for tropical heat covers ventilation.

Humidity. Warm, humid air carries a lot of water. Standard psychrometric tables put saturated air at 30 °C at about 30 g of water vapour per m³, roughly three times the figure at 10 °C. Much of that water condenses after compression. Size the aftercooler, drains and dryer for real tropical inlet conditions, not the reference conditions on the datasheet.

Dust. In the dry season, and in rice mills, cement works and feed mills all year, intake air can be dusty. Specify intake filtration to suit and plan for more frequent filter changes.

Power quality. Ask how the compressor and its drive tolerate voltage dips, imbalance and harmonics, and what protection is included. On a site with an unstable supply, this matters as much as efficiency.

Plan redundancy and expansion

Decide what happens when a compressor stops. If production cannot tolerate it, design N+1: enough capacity to meet peak demand with the largest machine out of service. Two or three right-sized machines often give better redundancy and better part-load efficiency than one large one.

Plan for growth too. Leave space, power and pipe connections for an extra machine, and size the ring main for future flow. Extending a well-planned compressor room costs less than rebuilding a cramped one. Good compressed air system design starts from this layout question.

Judge offers on lifecycle cost

The DOE sourcebook notes that a compressor’s purchase price is relatively low compared with the electricity it uses over its life, and recommends life-cycle cost analysis for compressed air decisions. In practice, the cheapest quotation is rarely the cheapest compressor.

Compare offers on specific power: package input power divided by delivered air at your working pressure, in kW per m³/min or kWh/m³. Ask for the manufacturer’s published performance data at the operating point you will use. Then add maintenance, parts and expected running hours. Our compressed air cost calculator turns those figures into an annual cost.

On savings, our position is simple. Savings are project-specific. We measure them against a baseline and verify them after implementation; we don’t promise a blanket percentage.

Questions to ask every compressor supplier

  • What is the FAD at my working pressure, and to which test standard was it measured?
  • What is the package input power and specific power at that point?
  • What control type is offered, and how does it perform at my measured part load?
  • What is the maximum ambient temperature rating, and what happens above it?
  • What dryer and filtration are included, and to which ISO 8573-1 class?
  • Which spare parts are stocked locally, and what is the service response?
  • What is included: installation, piping, electrical work, commissioning, training?

Where to go from here

If you already run compressors, measure before you replace anything. The data usually changes the answer, and sometimes shows that leak repair and better control defer a purchase altogether. If you are building new, bring the production plan, a layout and your quality requirements to the first meeting.

We are an authorised distributor of Ingersoll Rand and Sollant compressors, and we design, install and commission the complete system around them. Ask us which series are currently supplied in Cambodia, or try the system selector for a first view. Then talk to an engineer about your demand data.

Nexus Turnkey Engineering Team

Written and reviewed by the engineers who design, install and maintain industrial air systems for Nexus Turnkey in Cambodia. Questions about this article? Ask us directly.

FAQ

Questions engineers ask us

How do I know what size air compressor my factory needs?

Measure it. Log the flow and pressure of your existing system over at least one full production week, including nights and weekends. Size the compressors to the measured demand profile at the pressure you actually need, plus a planned allowance for expansion. Adding up nameplate ratings of every machine on the floor almost always oversizes the plant.

Is a bigger compressor safer?

Not usually. An oversized fixed-speed compressor spends much of its time unloaded, drawing power while delivering no air. An oversized variable-speed unit runs near the bottom of its speed range, where it is least efficient. Reliability comes from redundancy, such as a standby machine, not from oversizing one machine.

Do I need an oil-free compressor?

Only if your air quality requirement or risk assessment says that no compressor lubricant may enter the air, which is common for some food, beverage, pharmaceutical and electronics duties. Many plants meet their required ISO 8573-1 class with an oil-injected screw compressor and the right filtration. Define the class first, then choose the technology.

What should I compare between two compressor quotations?

Compare delivered air (FAD) at your working pressure, package power at that point, the specific power in kW per m3/min or kWh per m3, the control type, the maximum ambient temperature rating, and the scope of treatment, installation and service. Then compare lifecycle cost, of which electricity is usually the largest part.

Next step

Turn this into a plan for your plant.

Send us your situation and an engineer will reply with the questions that matter and a sensible next step.

Start typing to search